It's 10000 in size. Wow, haven't had such 1 be4.
Now folding the Project: 729 (Run 5, Clone 5, Gen 19).
Does any of you guys get these size of WU's?
That's a small 100 framer I think, only worth 11.7 points! One of machines (a 2500 Barton) is muching through an 8 pointer (project 814) at a frame every 5 minutes, but that one has 12,000 atoms to calulate rather than 200! What rate are you folding at on 729?
Check here (http://folding.stanford.edu/psummary.html) for the points per WU and project numbers. The biggest gromacs that I get tend to be 2,500,000, but this is misleading as most are still only 400 frames!
TL.
Hhmmzz, you're right, it goes quit fast:
[18:32:02] Writing local files
[18:32:04] Completed 2400000 out of 10000000 steps (24)
[18:34:44] Writing local files
[18:34:46] Completed 2500000 out of 10000000 steps (25)
[18:37:26] Writing local files
[18:37:28] Completed 2600000 out of 10000000 steps (26)
[18:40:09] Writing local files
[18:40:11] Completed 2700000 out of 10000000 steps (27)
[18:42:59] Writing local files
[18:43:01] Completed 2800000 out of 10000000 steps (28)
2 seconds to get to the next point. :unsure:
woot my new puta has munched thru its 1st half, and sent it, this is what was left from the oldf machien
wish i could just set that as a folding machine but its not gunna happen
I got a Barton 2500 running @ 1.87
I seems to take ages...
Should i try OCing it ? would that help much?
Ive only done 1 WU on this machine
400 in size.
21/400 on my next.
Should i use console version ? and set flags or somthing ive heard about :S
Faster ?
The Band of Crunchers have started ;) me and Blue have borged 10 ppl so far.
And they arnt the ppl i intended on ;)
Should i tell ppl to get the console version ?
Dan
Red
QuoteOriginally posted by Red_Thunder@Feb 11 2004, 10:15 AM
I got a Barton 2500 running @ 1.87
I seems to take ages...
Should i try OCing it ? would that help much?
Ive only done 1 WU on this machine
400 in size.
21/400 on my next.
Should i use console version ? and set flags or somthing ive heard about :S
Faster ?
The Band of Crunchers have started ;) me and Blue have borged 10 ppl so far.
And they arnt the ppl i intended on ;)
Should i tell ppl to get the console version ?
Dan
Red
Yes, use Console Version 4 - it folds faster than graphical. You need to enable SSE to get it to go quickly. With F@H version 4.0 there are some new flags added. If you want SSE enabled under version 4.0 and later then you need to add the flag -forcesse to your target line. My shortcut looks like this:
"C:\Documents and Settings\Paul\My Documents\My Received Files\Folding\FAH4Console.exe" -local -forcesse -advmethods
Existing users of version 3.25 beta would need to remove the -forcesse and replace it with -forceasm. -forceasm is not used under version 4 or later.
Enabling SSE will speed up your folding by about 30%. The start up note sin the console on a new WU should say 'SSE Enabled'. If it says 3DNow then you have done it wrong!
Next question will be: 'can I change the client in mid-WU?'. The answer here is YES! Just save the console client in the same folder as your current version. Edit the shortcut to point at the new version 4 console client, shut the old oen down, click the shortcut and version 4 will open up. Ignore the warnigns at the beginning, they are normal!
GL.
TL.
i just got a 600 part WU but each individual bit is 20 big
each 20point bit is taking about an hour so 30hours of folding at it should be done